""Clinical/Glass Thermometer Calibration Bath :  
 

WHY IS CALIBRATION NECESSARY ?
Temperature can not be measured entirely without error, so it is necessary to quantify these errors by calibration of the probe, with or without its associated display against the reference standard in the respective temperature range. Calibration is essential where traceability to a National Standard or International Standard in compliance to industrial requirement in ISO-9000 specification.

K.V.S. Temperature Heating/Water/Cooling/Clinical Baths may be used for temperature application like Calibration Measurement and Comparison of the Thermometers and Associate Instruments in the given range -20 C to 300 C. An electronic proportional band control adapts the heat supplied to the bath for thermal stability and uniformity requirements of the Bath for Comparison/Calibration.

 
Specifications
K.V.S. 300-H
High Temp. Oil Bath
K.V.S. 100-H
Water Bath
K.V.S. 20-H Low Temp. Bath
K.V.S. 50-H Clinical Thermometer
Bath
Working
Temperature Range
50 to 300°C
Amb. +5 to 100°C
-20 to Amb. °C
30 to 50°C
Resolution of Display
±0.1°C
±0.01°C
±0.1°C
±0.01°C
Overall Temp. Stability
±0.05°C
±0.02°C
±0.1°C
±0.02°C
Uniformity
±0.05°C
±0.02°C
±0.1°C
±0.02°C
Temperature Control
Microprocessor
Based PID with RTD PT-100
Microprocessor
Based PID with RTD PT-100
Microprocessor
Based PID with RTD PT-100
Microprocessor
Based PID with RTD PT-100
Heater Wattage
1000 Watt
750 Watt
750 Watt
250 Watt
PT-100 Sensor
3-Leads
3-Leads
3-Leads
3-Leads
Safety Installation
Drain Plug & Overflow Outlet for Expanded Bath Liquid
Drain Plug & Overflow Outlet for Expanded Bath Liquid
Drain Plug & Overflow Outlet for Expanded Bath Liquid
Drain Plug & Overflow Outlet for Expanded Bath Liquid
Stirrer Motor Power
1/8 hp, 1425 rpm
1/8 hp, 1425 rpm
1/8 hp, 1425 rpm
1/8 hp, 1425 rpm
Bath Opening Dia x Depth
100 x 500 mm
100 x 500 mm
150 x 500 mm
160 x 200 mm
Overall Dimension
400 x 400 x 600 mm
400 x 400 x 600 mm
450 x 450 x 600 mm
300 x 300 x 300 mm
Filling Volume
4.5 to 5.5 ltr
4.5 to 5.5 ltr
9 to 10 ltr
4.0 ltr.
Insulation - Fiber Wool & Puff
Not Less Than 135 mm
Not Less Than 135 mm
Not Less Than 135 mm
Not Less Than 100 mm
Mains Power Connections
220-240/50 V/Hz
220-240/50 V/Hz
220-240/50 V/Hz
220-240/50 V/Hz
Power Consumption
1500 Watt
850 Watt
3000 Watt
500 Watt
Permissible Ambient Temp.
10 to 35°C
10 to 35°C
10 to 35°C
10 to 27°C
 
Specifications :
Bath Material : S. S. 304 Grade
Wall Thickness of Sheet Material : 3 mm.
Insulation : Fiber Wool & Puff.
Thickness of Insulation : Not less than 135 mm.
Stirrer Type : Screw Type
Stirrer : Brass Stirrer L 400-425 mm x Ø 50 mm
Cover Plate of Bath Chamber : Hylem Sheet 19 mm thick to hold 5-6 Thermometers
 Ø of Holes in the Cover Plate :  mm 8(2), 6(2), 10(1), 12(1) other than for Control RTD and Heating Rod.

 
Thermometers Holding Clips : Phosphor Bronze
Stirrer Motor : ¼ h.p., 1425 R.P.M., Crompton Make.
Heating System : Nichrom Heater Winding 1200 W for Low Temp. Bath and 1000 W for Water & Oil Baths with 12-5A/230V AC.
Temp. Controller : Digital PID Temp. Indicator-cum-Controller & K.V. Make Digital Temp Indicator with Display 0.01°C upto 199°C.
Temperature Sensor : RTD Pt-100, Probe Type
Level Control of Fluid : Exit Pipe will be provided for Overflow of Bath Liquid.
Frame/Stand : A Stable Wheeled Metallic Frame to hold the Bath alongwith Control Panel will be provided. Proper arrangement for Tube Light will also be provided.
Compressor : Sriram/Kirloskar Make.